Brick Paver Installation & Edging



Staging of product

The majority of paver tasks will differ depending on access, website conditions, task size and naturally, the weather. These circumstances can have an overall impact on your project from a timing stand point. Careful consideration needs to be required to identify the time to start the paver installation. Constantly aim to avoid any traffic or decrease on the ready areas.

The supervisor or project manager should constantly have the products (sand/ pavers) distributed around the project website for easy and efficient installations. Paver pallets/bundles need to be put in a manner not to hinder the paver installation. The appropriate pallet/bundle placement can make the actual task installation simpler and quicker by decreasing the general labor of handling the product.

Brick paver patterns

Pavers can be put in many different patterns depending upon their shape. Each paver shape will typically have numerous various hatch patterns that are offered by the maker.

Specialists need to take into consideration the traffic weight loads on their paver tasks. In many applications around the world, it has been revealed that pavers laid in a herringbone pattern have carried out properly.

Pavers that are 60 mm (2 - 3/8 in) thickness are suitable for pedestrian applications. Pavers that are going to be used in industrial or industrial applications must be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that determine the beginning point of a paver project.

When beginning to set up pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a true straight string line above the surface area of the bedding sand at the ended up elevation of the pavers This will assist as a guide for maintaining straight joint lines and will likewise allow the installer to make modifications in the alignment of the pavers.

Buildings and concrete suppressing are typically not straight and need to not be used for developing straight joint lines. The usage of string lines is important to figure out the true straightness of the edge. As the paver installation advances, the string lines will help lessen the requirement for small trim pieces.

These will preserve a minimum joint width and allow the bedding and jointing sand to get in between each paver. Pavers with spacer bars are typically not laid in snug versus each other since a string line will offer constant joint spacing.

Installation of brick pavers.

One of the most commonly utilized methods for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along among the true straight lines that you have actually pulled or above the bedding sand. This will provide you a straight and real line off which to work. As soon as this row is established, you can continue to work outside into the field with the remainder of the pavers. Always make sure to occasionally inspect your joint lines to make sure they are straight and true. If not, adjustments to the pavers can be made as you continue installing. Pavers ought to be installed hand tight. The best technique is to put a paver versus another one and let it slide down into the bedding sand. Do not kick or tap the pavers into location as this can toss your lines out of real straightness.

When setting up pavers on a steep grade, they ought to be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

The best way for setting up pavers on big tasks is to install them mechanically. There are a couple items a contractor ought to think about prior to setting up pavers mechanically:

1.) Mechanical installers are just efficient in setting up pavers in certain patterns.

2.) The contractor should ensure that the producer can production and bundling pavers in the wanted pattern on the pallets for easy mechanical installation.

3.) Contractors may encounter a color blending circumstance Patio Pavers West Palm Beach coming off the packages of pavers Poor color mixing might lead to an irregular looking installation. The majority of producers are consistent with color mixing on each package of pavers, however it is the contractor's responsibility to ensure proper blending in the field.

Cutting procedures for brick pavers.

Contractors generally have two ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will provide a much cleaner and more accurate cut. Most brick saws will have a hose attachment on them which will allow the operator to cut the pavers damp. When cutting pavers wet, it will help reduce dust and will prolong the diamond blades life. The operator of the brick saw should always cut the pavers away from the surface area of the paver field when cutting damp, due to that the pavers will produce a slurry that will stain the paver surface area. Pavers that are cut ought to not fit tight, adequate spacing ought to be available for jointing sand.

The brick saw operator should constantly wear the proper protection that is required for running a saw, such as eye, ear, breathing and hand security ).

Edging types

Edge restraints play a major role in the total success of an interlocking pavement installation Edging restraints remove lateral motion of the pavers and hold the pavers firmly together. Especially at the outer border of the paver application, without an edging restraint, your task is guaranteed to fail over time.

Normally made edge restraints are the most frequently used by contractors. Manufactured edging restraints can vary from, plastic edging, steel and aluminum, woods or precast concrete and stone.

Edging installation.

When installing your edge restraint, it ought to rest directly on top of the compressed gravel base. The compressed gravel base course ought to extend a minimum of 6in beyond the perimeter of the pavers This will supply an appropriate foundation upon which the edging restraint can sit. Made edging (i.E. Plastic, steel or aluminum) need to be securely anchored into the compacted gravel base( contact the producer's literature for the recommended spacing of the spikes). There are some edging restraints that will extend much deeper into the gravel base or beyond the base course (i.E. Timbers or poured-in-place curbs ). Edging restraints need to never ever be placed straight on top of the bed linen sand. This could lead to the migration of the bed linen sand and ultimate lateral movement of the pavers. If there is a possibility of losing bedding sand between the pavers and the edge restraint, then geo textile fabric is advised. When a space between the pavers and the edging exceeds 3/8" (10mm), then the area ought to be filled with cut pavers. All edging applications need to be appropriately back filled after they are installed to help offer additional stability.

Compaction of brick pavers.

After installation, the pavers need to be compressed. The entire location that is to be compacted need to be swept clean of any foreign things and particles that can cause scuffing or scratching on the surface of the pavers.

In addition, it is crucial that the first compaction takes location before any jointing sand has been used to the pavers. If jointing sand is applied to the pavers prior to compaction takes place, this can cause a bridging issue and will not allow the joints to be totally filled with jointing sand. This can also prevent the pavers from being effectively set into the bedding sand.

When condensing the pavers, it is suggested that you make at least 2 passes in different instructions across the pavers. This will enable the pavers to be effectively set in the bed linen sand and will require the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is really critical to the final efficiency of the pavers. Failure to do proper compaction can result in contortions and pavement failure over time.


Paver pallets/bundles must be positioned in a manner not to interfere with the paver installation. One of the most commonly utilized methods for the installation of pavers is hand installation of each paver. The operator of the brick saw must constantly cut the pavers away from the surface of the paver field when cutting damp, due to the reality that the pavers will create a slurry that will stain the paver surface. Edging restraints remove lateral movement of the pavers and hold the pavers firmly together. When a space in between the pavers and the edging exceeds 3/8" (10mm), then the space needs to be filled with cut pavers.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Brick Paver Installation & Edging”

Leave a Reply

Gravatar